VIVADO中常用的TCL脚本

地址在excel中递增公式0xIF(LEN(DEC2HEX((ROW(A1)-1)*4))4,REPT(0,4-LEN(DEC2HEX((ROW(A1)-1)*4)))DEC2HEX((ROW(A1)-1)*4),DEC2HEX((ROW(A1)-1)*4))更改端口属性在properties中对应CONFIG行修改set_property CONFIG.FREQ_HZ 156250000 [get_bd_pins /aurora_64b66b_0_CLOC_0/USER_CLK] set_property CONFIG.FREQ_HZ 312500000 [get_bd_pins /aurora_64b66b_0_CLOC_0/SYNC_CLK] set_property CONFIG.POLARITY ACTIVE_HIGH [get_bd_pins /aurora_64b66b_0_SUPP_0/SYSTEM_RESET]同端口下一键换连create_bd_cell -type ip -vlnv xilinx.com:user:Pcie_DMAmm_top_v5:1.0 PR_MOD/hier_0/Pcie_DMAmm_top_v5_0 replace_bd_cell [get_bd_cells PR_MOD/hier_0/Pcie_DMAmm_top_v3_0] [get_bd_cells PR_MOD/hier_0/Pcie_DMAmm_top_v5_0]批量连接连小线不利于布局布线器优化推荐连接总线startgroup set NAMESRC BRAM_1TO2_M0_idc0 set NAMEDST split_64to32_bram_2 set n1 output_bram0 connect_bd_net [get_bd_pins PR_MOD/$NAMESRC/bram_rst_in] [get_bd_pins PR_MOD/$NAMEDST/${n1}_Rst_A] connect_bd_net [get_bd_pins PR_MOD/$NAMESRC/bram_clk] [get_bd_pins PR_MOD/$NAMEDST/${n1}_Clk_A] connect_bd_net [get_bd_pins PR_MOD/$NAMESRC/bram_din] [get_bd_pins PR_MOD/$NAMEDST/${n1}_Din_A] connect_bd_net [get_bd_pins PR_MOD/$NAMESRC/bram_en] [get_bd_pins PR_MOD/$NAMEDST/${n1}_EN_A] connect_bd_net [get_bd_pins PR_MOD/$NAMESRC/bram_dout] [get_bd_pins PR_MOD/$NAMEDST/${n1}_Dout_A] connect_bd_net [get_bd_pins PR_MOD/$NAMESRC/bram_we] [get_bd_pins PR_MOD/$NAMEDST/${n1}_WEN_A] connect_bd_net [get_bd_pins PR_MOD/$NAMESRC/bram_addr_in] [get_bd_pins PR_MOD/$NAMEDST/${n1}_Addr_A] endgroup在sub创建端口ctrl k 创建单个端口for {set i 1} {$i85} {incr i} { set y [expr 85$i] set n1 cmda_output_$i set n2 out_ch$y startgroup create_bd_pin -dir O -from 31 -to 0 CDMA_DOWN/$n2 connect_bd_net [get_bd_pins CDMA_DOWN/$n2] [get_bd_pins CDMA_DOWN/ao_delay_mux_1/$n1] endgroup }BD模块中的快速连线for {set i 0} {$i384} {incr i} { set n1 chan_out_$i append n1 _ap_vld set n2 ch$i append n2 _in_vld connect_bd_net [get_bd_pins CDMA_DOWN/bram2chan_384_0/$n1] [get_bd_pins CDMA_DOWN/posedge_lock_mod_384_0/$n2] }n1、n2为需要连接的端口名称端口名称更改for {set i 0} {$i16} {incr i} { set y [expr 16$i] set n1 In$i append n1 _1 set n2 DI$y set_property name $n2 [get_bd_ports $n1] }n1为旧名称n2为新名称触发本地自动编译1、新建xxx.tcl文件内容如下open_project project_1.xpr reset_run synth_1 launch_runs synth_1 wait_on_run synth_1 launch_runs impl_1 -to_step write_bitstream -jobs 8 wait_on_run impl_1 write_hw_platform -fixed -include_bit -force -file ./project_1.xsa close_project2、cmd触发自动编译cd C:\........\project_1\prj(进入工程所在路径)call F:\...(vivado安装路径).....\Vivado\2018.2\bin\vivado.bat -mode batch -source xxx.tcl